IproMac e.K. Willi Schneegaß - Stockist for used machines

turning diameter 100 bis 400 mm︱tool taper SO ︱weight 30 t︱control Siemens 840 D ︱

---

Ball machining center Special facility for balls 100 to 400 mm A viewing and demonstration is possible by appointment.

turning diameter 554 mm︱turning length 1000 mm︱control Fanuc ︱total power requirement 11 kW︱weight of the machine ca. 2,7 t︱dimensions of the machine ca. 2,6 x 1,6 x 1,8 m︱

---

HARRISON alpha 550 cycle lathe, used Controller: Fanuc Turning diameter: 554 mm Turning length: 1,000 mm Spindle passage: 90 mm Spindle: Speed (max.): 1,800 rpm Speed levels: 9 Power: 11kW Spindle passage (approx.): 90 mm Workpiece clamping: 3-jaw chuck, ø315 mm Tool carrier: Technology: quick-change holder on cross slide Travel in X: 310 mm Tailstock: Technology: Manual tailstock Quill ø: 95 mm Stroke: 145mm Taper: MK 6 Equipment/accessories: Chip management: chip tray Coolant management: KSS pump Shaft Machining: Fixed Bezel

x-travel 800 mm︱y-travel 800 mm︱z-travel 710 mm︱Control Heller Unipro 90 ︱total power requirement 62 kW︱weight of the machine ca. 17 t︱dimensions of the machine ca. m︱

---

A Heller MCP-H 250, built in 1999, is for sale. The machine is expected to be available in February 2024 and can be viewed under power. Description Heller MCP H 250 Machine number 32-44117 Year of construction 1999 Control system: Heller Unipro 90 Spindle taper: SK50 Spindle speed: 45-6000 1/min Pallet size: 630x 500 mm Maximum table load (even): 800 daN Max. interference contour workpiece size: 900x1000 mm NC round table Pallet changing device Tool magazine chain: 52 places Longitudinal stroke axis X: 800 mm Cross stroke axis Z: 710 mm Vertical stroke axis Y: 800mm Machine weight: 16200 daN Power requirement: 62 KVA Furnishing: Measuring device for BLUM TC 50 Linear scales Heidenhain BKW cooling unit for spindle cooling Knoll coolant system with vacuum rotation filter and sludge discharge Knoll chip conveyor BKW cooling unit for cooling lubricant system Work area flushing 2 pallets Machine is in very good condition considering its age. Annual maintenance was carried out throughout its lifespan. In 2018 the machine was retrofitted with the latest interface/receiver for the Blum TC 50 measuring probe.

x-travel 550 mm︱y-travel 300 mm︱z-travel 425 mm︱tool taper SK 40 ︱control Siemens 840 D ︱total power requirement 12 KVA︱weight of the machine ca. 5 t︱transport dimensions LxWxH 2,1 x 3,1 x 3,0 m︱

---

chiron fz 12 wm with changeable plate with 2 x 4. axis PEISELER WIth ONTROL SIEMENS 810

x-travel 400 mm︱y-travel 320 mm︱z-travel 400 mm︱Control Heidenhain TNC 426/430 ︱tool taper SK 40 ︱spindle turning speed range 5000 U/min︱total power requirement 5,5 kW︱weight of the machine ca. 2 t︱dimensions of the machine ca. 2,5 x 2,0 x 2,0 m︱

---

1 used Universal tool milling machine Make KUNZMANN Type WF 4 CNC Built in 2002 with Heidenhain TNC 426/430 Operating hours: Control on: 39893 h Machine on: 36335 h Program run: 5705 h Spindle running time: 8287 h Automatic tool suit, drilling quill Milling head swivels +/- 90° (without vice) A viewing is possible at any time by arrangement.

x-travel 3000 mm︱y-travel 800 mm︱z-travel 1100 mm︱Control ︱total power requirement 60 kW︱weight of the machine ca. 15 t︱dimensions of the machine ca. 7,0 X 6,0 X 4,0 m︱

---

For sale is a Matec 30 HV machine number 569 built in 2003. The machine is expected to be released in August 2024 and can be used under Electricity can be visited. The machine has been serviced every year and is technical in a good condition. Manufacturer: Matec Maschinenbau Type: 30HV Machine number: 569 Year of construction: 11/2003 Control: Bosch Type 3 Osa control x-travel 3,000 mm y-travel 800 mm z-travel 1100 mm Main spindle: Type DMS 112 speed range - main spindle max. 12,000 min/-1 Drive power - main spindle 30 kW Max. Torque 190 Nm Tool holder HSK 63 A Drilling capacity steel approx. 60mm Milling capacity approx. 500 cm³ Thread cutting M30 Feeds: Rapid traverse (X / Y / Z) 30 m/min Feed speed 30,000 mm/min NC swivel head:Sauter pivotable +/- 90° division +/- 3 arc seconds Work table: table surface area 3,500 x 835 mm T-slots 7x T-slots - width 18-H7 NC round table Sempuco SKH 4/630 Horizontal face plate Faceplate diameter 630mm (embedded in the machine table) Tool changer: Number of tool locations 48 pos. Total connection value: 60KVA Machine weight approx. 15 t Space requirement approx. 7.0 x 6.0 x 4.0 m, fully encapsulated working space Loading doors suitable for crane loading Automatic opening Movable partition coolant device: Internal coolant supply 70 bar Paper band filter Flush gun Chip conveyor ejection height 1200mm Miscellaneous: Clamping hydraulic interface 4th axis 3D wireless measuring probe Direct measuring systems x-y-z Cooling unit for control cabinet NC round table RW/NC 160/250 Hofmann Faceplate diameter 250mm Peak height 160mm Hydraulic tailstock with quill MK4 documentation Declaration of Conformity Replacement screen installed

honing diameter 1-60 mm︱stroke 350 mm︱Control Unipo upc 1500 ︱centre height 350 mm︱total power requirement 21 kW︱weight of the machine ca. 6,5 t︱dimensions of the machine ca. 4,0 X 3,5 X 3,2 m︱

---

Vertical honing machine with deburring unit and measuring station Kadia 2PH 60/350 T A vertical honing machine Kadia 2PH 60/350 T is for sale. In addition to the honing function, a deburring unit and a measuring station are integrated into the machine. The machine is expected to be released in February 2024 and can be viewed under power. The machine has been serviced according to the prescribed intervals and is technically in perfect condition. Manufacturer: Kadia Production GmbH + Co Type: 2PH 60/350 T Machine number: 50/1776 Year of construction: 1998 Installation length: 4.0 m Installation width: 3.5 m Installation height: 3.2 m Transport weight: 6000 kg Machine weight: 4500 kg Hydraulic unit: 400 kg Coolant system: 600 kg Air requirement: max. 1.2 m3/h Control: Unipo upc 1500 Total connection value: approx. 21 kVA Total power requirement: 18 kW Voltage: 230/400V Frequency: 50Hz Spindle motors: Quantity: 2 ST Type: SEW DTF100L4TH Max. speed: 1400 min-1 Power: 3kW Current: 11.4 / 6.6 A Coolant pump: Type: Brinkmann TE143/200/1001/min Speed: 2850 rpm Power: 1.5 kW Current: 6.1/3.5A Bust unit: Type: SEW DT90L8/4 Speed: 700/1400 rpm Power: 0.44/0.55 kW Current: 2.1/2.2A Hydraulic pump: Type: Siemens 1LAF7163-4AA61 Speed: 1460 rpm Power: 11 kW Current: 21.5 A, Scope of application: Vertical honing Deburring Measuring and testing Accesories:

cutting diameter 650 x 650 mm︱saw band length 8585 mm︱cutting width 1,6 mm︱band speed 18 - 120 m/min︱Control KASTO ︱table load 8 t︱total power requirement 18 kW︱weight of the machine ca. 7 t︱dimensions of the machine ca. m︱

---

Automatic band saw Kasto HBA 660 AU Accesories: chip conveyor

cutting diameter 670 mm︱saw band length 8800 mm︱cutting width 1,6 mm︱band speed 16 - 100 m/min︱table load 15 t︱total power requirement 18 kW︱weight of the machine ca. 7 t︱dimensions of the machine ca. m︱

---

Automatic band saw Behringer HBP 650 A

table length 3000 mm︱table width 1500 mm︱burner heads 1 ︱Control Trumpf ︱total power requirement 73 kW︱

---

Laser cutting machine Trumpf TruLaser 3030 Lean Edition Laser power 3200W Type L 20 Year of construction 2012 Net 400V/50Hz Total power requirement 73 kVA Control voltage 24V Fuse 3 x 125 A Air connection 7-10 bar Nitrogen connection 30 bar Oxygen connection 20 bar Beam one hour 7755 Laser one hour 25263 Machine is in very good condition and optimized by Trumpf in 12/2022. Documentation: Completely available

x-axis 2000 mm︱y-axis 1500 mm︱z-axis 750 mm︱burner heads 1 3 D︱laser capacity in Watt 2700 ︱

---

3D laser cutting and welding system TruLaser Cell 7020 Machine no. A0421A0099 Type: L13 standard equipment - X = 2000, Z = 750mm; B = +/- 135°; C = n x 360° - Laser TruFlow 2700 - Position laser diode - Stationary, rotatable pendant control panel - Teach panel - Teach software - Magnetic clutch, head detection - Laser power control - Power Cycles - Logbook function - focus line - Nitrogen jet aeration - Network connection including installation via teleservice - Analog modem for teleservice - Lighting boom - Documentation twice Deviating from this standard equipment or in addition the machine TruLaser Cell 7020 is equipped with: With the following configuration: Frequency 50Hz Voltage 400 V0 Electrical regulation IEC Language operating instructions German Number of operating instructions 2 pc Color standard RAL9002/5010 TruFlow 2700 Laser cutting (including preparation for laser welding) Incl. 2 cutting gases (02, N2), APC distance control, p Programmable cutting gas selection, adjustment device, Analog value cutting, pressure setting, valves Additional cutting gas argon Cutting optics f = 155 mm incl. sensor Stationary table 2000x1500 mm Second cutting optics (240 mm) Work table suction system including piping Compact deduster with 2000 Nm3/h including spark pre-separator, extraction pipe connection, for 1 active extraction point Protective cabin including separate extraction Special cover of the cabin top / roof Automatic sliding door in front Control panel including multi-button, acknowledgment and emergency stop Documentation twice / German The machine is delivered without additional Programming software, post processor and operator course. Annual service by Trumpf Service with proof Operating hours / as of 02/2022 Machine hours: 40,600h Laser on: 39,200h Beam on: 6,900h Last laser power measurement = 2790 watts (Optional) On request, we can also take care of the construction and commissioning through our laser service including training of your staff and a guarantee of 12 months (price on request)

x-travel 730 mm︱y-travel 730 mm︱z-travel 880 mm︱control 840 D sl Siemens︱size of pallet 500 X 500 mm︱total power requirement 46,2 kW︱weight of the machine ca. 15 t︱dimensions of the machine ca. 5,5 X 3,0 X 2,8 m︱

---

CNC machining center horizontal DMG MORI-NHX 5000 - 2-fold pallet changer - 15.094h spindle hours Technical details / accessories / supplement: x-travel 730 mm y-travel 730 mm z-travel 880 mm Control 840 D sl Siemens main spindle: max. spindle speed 12,000 rpm Drive power - milling spindle 30 kW Max torque 102Nm Tool holder SK 40 Distance spindle center to table 80 - 810 mm Distance spindle nose and table center 70 - 950 mm Pallet changer: Number of pallets 2 Pallet size 500 x 500 mm max. workpiece weight 500 kg max. workpiece diameter 800 mm max. workpiece height 1,100 mm Pallet change time 9.5 seconds Indexing time 1.3 sec B axis (table) 360 x 1° tool changer: Number of tool places 40 pos. Tool holder SK 40 maximum tool diameter 110 mm max. tool dia. with a free neighboring box. 320mm maximum tool length 550 mm max. tool weight 30.0 kg Changing time tool - tool 1.95 sec Changeover time Span - Span 4.4 - 10.0 sec feeds: Rapid traverse 60 m/min Feed speed max. 60,000 mm/min Inching feed speed 0 - 5,000 mm/min Total power requirement 46.2 kVA Machine weight approx. 15.0 t Space requirement approx. 5.5 x 3.0 x 2.8 m documentation chip conveyor coolant device High pressure cooling 40 bar internal coolant supply tool changer B axis 1° pallet changer Accessories (optional) Probe Renishaw PP 60 opt. approx. 70 recordings SK 40 (partly with tools)

feed pressure 30 bar︱liter capacity 2900 / min l︱total power requirement 7,5 kW︱

---

voltage 230 V︱current 16 A︱output 3 kw︱working pressure 6 bar︱Number of boilers 1 ︱Steam production 5 kg/h︱Boiler temperature 165 °C︱Temperature at the nozzle (Steam) 120 °C︱Temperature at the nozzle (Steam+Water/Detergent) 90 °C︱Water tank capacity 5 l︱Detergent tank capacity 5 l︱water consumption 3,5 l/h︱Maximum length of hose 4 m︱Setting at work 4 min︱Working hours per day 24 h︱Predisosed for suction facility ja ︱length 500 mm︱width 450 mm︱height 850 mm︱weight 28 kg︱

---

Dry steam cleaner with suction Mach. No. 3449/19 TECHNICAL SPECIFICATIONS DRY VACUUM CLEANER - 3 circuit system steam steam and water + detergent Suction with blowing function - Voltage 220V 50Hz - Power 3000 watts - Steam production 5 kg/h - temperature 165°C in the boiler, up to 120°C at the nozzle outlet - Steam pressure 6 bar - Water tank 1 x 5 l (enough for approx. 1.5 hours) - Detergent tank 1 x 5 l - Mobile - Connection cable 5 m long - Case stainless steel - Dimensions L 500 x W 450 x H 850 mm - Weight 28kg - Ready to use in 4 minutes incl. accessories NEW PRICE EURO 2950,-

voltage 400 V︱current 32 A︱output 18 kw︱Production at 15462 kcal/h︱working pressure 10 bar︱Number of boilers 2 ︱Steam production 30 kg/h︱Boiler temperature 179 °C︱Temperature at the nozzle (Steam) 150 °C︱Temperature at the nozzle (Steam+Water/Detergent) 100 °C︱Water tank capacity 110 l︱Detergent tank capacity 2 x 1,4 l︱water consumption 30 l/h︱Maximum length of hose 8 m︱Setting at work 5 min︱Working hours per day 24 h︱Predisosed for suction facility ja ︱length 1055 mm︱width 700 mm︱height 815 mm︱

---

Electronic steam generator and cleaning system Masch. No. 90106/05 - Electronically controlled - 3 circuit system steam steam and water Steam and water cleaning agents - Voltage 400V/3-phase - Connection cable 5-pin, 8m long - Auto polarity switch - Power 18,000 watts - Temperature 180°C in the boiler up to 120-150°C at the nozzle outlet - Temperature of steam-water mixture up to 100° C - Steam pressure max. 10 bar - Storage tank 1 x 110 l - Detergent concentrate containers 2 x 1.4 l - Additive dosing system - Connection for vacuum cleaner 400 V / 3-phase - mobile / 2 wheels lockable - Hangers for hose and connection cable - Housing powder-coated RAL 5015 - Dimensions L1055 x W700 x H815 - Weight 165 kg Accesories: Hose package 4m analogue (IP10/03) Lance long 78 cm Completely workshop tested and repaired - Test according to BGV-A3 - Test run 1 hour

voltage 400 V︱current 32 A︱output 18 kw︱Production at 15462 kcal/h︱working pressure 10 bar︱Number of boilers 2 ︱Steam production 30 kg/h︱Boiler temperature 179 °C︱Temperature at the nozzle (Steam) 150 °C︱Temperature at the nozzle (Steam+Water/Detergent) 100 °C︱Water tank capacity 110 l︱Detergent tank capacity 1,4 l︱water consumption 30 l/h︱Maximum length of hose 8 m︱Setting at work 5 min︱Working hours per day 24 h︱Predisosed for suction facility ja ︱length 1610 mm︱width 470 mm︱height 1300 mm︱

---

Stationary steam generator and cleaning system Mach. No. 1300016/03 - Electronically controlled - 1 workstation connection - 2 circuit system steam steam and detergent - Voltage 400V/3-phase - Auto polarity switch - Power 18 KW - Heat output 15,462 kcal/h - Working pressure max. 10 bar - Number of steam generators 2 - Stainless steel boiler - Steam output 30 kg/h - Temperature 188°C in the boiler - Temperature at the nozzle outlet (steam) 120-150° C - Water consumption 30 l/h (at 100% utilization) - Temperature at the nozzle outlet (steam + cleaning agent) 100° C - Main steam valve - Electropneumatic - 5 l detergent concentrate container - Operating hours display230 - Case stainless steel - Dimensions approx. 1610 x 470 x 1300 mm - Weight 230 kg completely workshop tested and overhauled.

degree 1200 ︱length 2250 mm︱width 1450 mm︱depth 2000 mm︱pan capacity 320 Kg / Al︱capacity 840 u/F︱total power requirement 102 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. m︱

---

NEW GOODS with manufacturer guarantee ORIGINAL PACKAGED Melting electric tilting furnace PTS 970 /12 Technical parameters Mark: PTS 970/12 Max. temperature: 1200 °C Recommended range of operating temperatures: 650-1000 °C (in crucible) Capacity: 840 kg of Al Crucible type Noltina or equivalent: TBNS 800 Capacity of crucible: 320 l External dimensions (w x h x d): 2250 x 2450 x 2000 mm Melting output**: 250 kg of Al alloys/h Heating power input: 102 kW Weight: 3500 kg Protection*: 200/3 Voltage: 3/N/PE 400/230 V AC 50 Hz *Protection can vary depending on the accessories chosen (at additional cost). **The melting output values specified in the table are the maximum values. They are achievable if the conditions mentionedbelow are complied with. Approximately 80 % of the maximum value of the melting output is achieved during actualoperation. Description The furnace is used as a melting device with the possibility of tilting and pouring the melt into the transport pan or transport holding furnace for subsequent processing at temperatures up to 1200 °C (in the furnace chamber, approximately 1100 °C in a crucible – these values are guaranteed only when using unworn Noltina crucible of the appropriate size). Standard design of furnace •Crucible •Hydraulic furnace tilting •Ht40T controller •Limit unit •Protective collar of crucible •Manual lid •Emergency drain at the bottom of the furnace, with flap •“S” type limiting and controlling thermocouple •3 ammeters for checking the status of the heating elements •Switching of the heaters using contactors •Residual current protector •Legs to facilitate handling by a forklift at volumes of 400 l or more •Connection between the furnace and switchboard, within a metal hose with a plasticprotector, length of up to 5 m •Wall switchboard •Hydraulic aggregate is on the right side of the furnace, the hand lever control is on the rightside of the furnace Benefits: • Furnace chamber with a long-term service life, mechanical durability and resistance to corrosion • Simple replacement of the spirals if they become damaged • Simple replacement of the crucible by dismounting the top furnace cover • Use of the lid reduces operational costs • Robust, durable design for heavy-duty operations • The chamber is provided with an emergency drain with an insulated flap so that it is protected against damage in the event of melt leakage from the crucible • Easy to install, easy to control • Custom adjustments • 24-month warranty • Mechanical durability • High melting output

degree 1200 ︱length 2250 mm︱width 1450 mm︱depth 2000 mm︱pan capacity 320 Kg / Al︱capacity 840 u/F︱total power requirement 102 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. m︱

---

NEW GOODS with manufacturer guarantee ORIGINAL PACKAGED Melting electric tilting furnace PTS 970 /12 Technical parameters Mark: PTS 970/12 Max. temperature: 1200 °C Recommended range of operating temperatures: 650-1000 °C (in crucible) Capacity: 840 kg of Al Crucible type Noltina or equivalent: TBNS 800 Capacity of crucible: 320 l External dimensions (w x h x d): 2250 x 2450 x 2000 mm Melting output**: 250 kg of Al alloys/h Heating power input: 102 kW Weight: 3500 kg Protection*: 200/3 Voltage: 3/N/PE 400/230 V AC 50 Hz *Protection can vary depending on the accessories chosen (at additional cost). **The melting output values specified in the table are the maximum values. They are achievable if the conditions mentionedbelow are complied with. Approximately 80 % of the maximum value of the melting output is achieved during actualoperation. Description The furnace is used as a melting device with the possibility of tilting and pouring the melt into the transport pan or transport holding furnace for subsequent processing at temperatures up to 1200 °C (in the furnace chamber, approximately 1100 °C in a crucible – these values are guaranteed only when using unworn Noltina crucible of the appropriate size). Standard design of furnace •Crucible •Hydraulic furnace tilting •Ht40T controller •Limit unit •Protective collar of crucible •Manual lid •Emergency drain at the bottom of the furnace, with flap •“S” type limiting and controlling thermocouple •3 ammeters for checking the status of the heating elements •Switching of the heaters using contactors •Residual current protector •Legs to facilitate handling by a forklift at volumes of 400 l or more •Connection between the furnace and switchboard, within a metal hose with a plasticprotector, length of up to 5 m •Wall switchboard •Hydraulic aggregate is on the right side of the furnace, the hand lever control is on the rightside of the furnace Benefits: • Furnace chamber with a long-term service life, mechanical durability and resistance to corrosion • Simple replacement of the spirals if they become damaged • Simple replacement of the crucible by dismounting the top furnace cover • Use of the lid reduces operational costs • Robust, durable design for heavy-duty operations • The chamber is provided with an emergency drain with an insulated flap so that it is protected against damage in the event of melt leakage from the crucible • Easy to install, easy to control • Custom adjustments • 24-month warranty • Mechanical durability • High melting output

degree 1200 ︱length 2250 mm︱width 1450 mm︱depth 2000 mm︱pan capacity 320 Kg / Al︱capacity 840 u/F︱total power requirement 102 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. m︱

---

NEW GOODS with manufacturer guarantee ORIGINAL PACKAGED Melting electric tilting furnace PTS 970 /12 Technical parameters Mark: PTS 970/12 Max. temperature: 1200 °C Recommended range of operating temperatures: 650-1000 °C (in crucible) Capacity: 840 kg of Al Crucible type Noltina or equivalent: TBNS 800 Capacity of crucible: 320 l External dimensions (w x h x d): 2250 x 2450 x 2000 mm Melting output**: 250 kg of Al alloys/h Heating power input: 102 kW Weight: 3500 kg Protection*: 200/3 Voltage: 3/N/PE 400/230 V AC 50 Hz *Protection can vary depending on the accessories chosen (at additional cost). **The melting output values specified in the table are the maximum values. They are achievable if the conditions mentionedbelow are complied with. Approximately 80 % of the maximum value of the melting output is achieved during actualoperation. Description The furnace is used as a melting device with the possibility of tilting and pouring the melt into the transport pan or transport holding furnace for subsequent processing at temperatures up to 1200 °C (in the furnace chamber, approximately 1100 °C in a crucible – these values are guaranteed only when using unworn Noltina crucible of the appropriate size). Standard design of furnace •Crucible •Hydraulic furnace tilting •Ht40T controller •Limit unit •Protective collar of crucible •Manual lid •Emergency drain at the bottom of the furnace, with flap •“S” type limiting and controlling thermocouple •3 ammeters for checking the status of the heating elements •Switching of the heaters using contactors •Residual current protector •Legs to facilitate handling by a forklift at volumes of 400 l or more •Connection between the furnace and switchboard, within a metal hose with a plasticprotector, length of up to 5 m •Wall switchboard •Hydraulic aggregate is on the right side of the furnace, the hand lever control is on the rightside of the furnace Benefits: • Furnace chamber with a long-term service life, mechanical durability and resistance to corrosion • Simple replacement of the spirals if they become damaged • Simple replacement of the crucible by dismounting the top furnace cover • Use of the lid reduces operational costs • Robust, durable design for heavy-duty operations • The chamber is provided with an emergency drain with an insulated flap so that it is protected against damage in the event of melt leakage from the crucible • Easy to install, easy to control • Custom adjustments • 24-month warranty • Mechanical durability • High melting output

degree 1200 ︱length 2250 mm︱width 1450 mm︱depth 2000 mm︱pan capacity 320 Kg / Al︱capacity 840 u/F︱total power requirement 102 kW︱weight of the machine ca. 3,5 t︱dimensions of the machine ca. m︱

---

NEW GOODS with manufacturer guarantee ORIGINAL PACKAGED Melting electric tilting furnace PTS 970 /12 Technical parameters Mark: PTS 970/12 Max. temperature: 1200 °C Recommended range of operating temperatures: 650-1000 °C (in crucible) Capacity: 840 kg of Al Crucible type Noltina or equivalent: TBNS 800 Capacity of crucible: 320 l External dimensions (w x h x d): 2250 x 2450 x 2000 mm Melting output**: 250 kg of Al alloys/h Heating power input: 102 kW Weight: 3500 kg Protection*: 200/3 Voltage: 3/N/PE 400/230 V AC 50 Hz *Protection can vary depending on the accessories chosen (at additional cost). **The melting output values specified in the table are the maximum values. They are achievable if the conditions mentionedbelow are complied with. Approximately 80 % of the maximum value of the melting output is achieved during actualoperation. Description The furnace is used as a melting device with the possibility of tilting and pouring the melt into the transport pan or transport holding furnace for subsequent processing at temperatures up to 1200 °C (in the furnace chamber, approximately 1100 °C in a crucible – these values are guaranteed only when using unworn Noltina crucible of the appropriate size). Standard design of furnace •Crucible •Hydraulic furnace tilting •Ht40T controller •Limit unit •Protective collar of crucible •Manual lid •Emergency drain at the bottom of the furnace, with flap •“S” type limiting and controlling thermocouple •3 ammeters for checking the status of the heating elements •Switching of the heaters using contactors •Residual current protector •Legs to facilitate handling by a forklift at volumes of 400 l or more •Connection between the furnace and switchboard, within a metal hose with a plasticprotector, length of up to 5 m •Wall switchboard •Hydraulic aggregate is on the right side of the furnace, the hand lever control is on the rightside of the furnace Benefits: • Furnace chamber with a long-term service life, mechanical durability and resistance to corrosion • Simple replacement of the spirals if they become damaged • Simple replacement of the crucible by dismounting the top furnace cover • Use of the lid reduces operational costs • Robust, durable design for heavy-duty operations • The chamber is provided with an emergency drain with an insulated flap so that it is protected against damage in the event of melt leakage from the crucible • Easy to install, easy to control • Custom adjustments • 24-month warranty • Mechanical durability • High melting output